POLYMAC ERGHO 7 SINGLE SIDED EDGEBANDER
Equipment Location: Sauk Rapids, MN
| Lot Closes: |
|
(6/19/2014 3:16 PM EST)
|
|
Event:
|
|
SAUK RAPIDS WOODWORKING
|
|
Brand/Model:
|
|
POLYMAC "ERGHO 7"
|
|
Year MFG:
|
|
2001
|
|
Machine Type:
|
|
SINGLE SIDED EDGEBANDER
|
|
Serial #:
|
|
15458
|
|
Elect./Voltage:
|
|
220V, 60 Cy, 3 Ph.
|
|
Location:
|
|
Sauk Rapids, MN
|
|
Condition:
|
|
Good condition
|
| *Dimensions: | | 252" L x 42" W x 64" H |
| *Weight: | | 6,600 Lbs (estimate) |
|
Loading:
|
|
$ 300 Loading fee
|
|
Comment:
|
|
Under power and ready for inspection. Click on the "event details" tab for inspection details.
|
|
Buyer Premium:
|
|
12.5%
|
Description:
(view full)
0.4 - 15mm capacity with 10 & 20 m/min feed speed; Min. panel width 85 mm & Min. length 160 mm, max. panel thickness 45 mm; automatic strip & coil feed magazine with robust shear type 3 mm PVC guillotine.Teflon coated Hot Melt glue pot, digital thermostats with automatic kick down when machine is in idle mode; dual temperature control Pressure section with (1) large dia. "non-stick" coated drive roller & (3) chrome plated pneumatic inclined pressure controlled idle rollers; horiz. adj. w/digital indicator. Workstations: Front & rear end trims (0.5 HP - 12,000 RPM motors), motors travel on 45° slides and pneumatic tilt 0° - 15° on horz. plane. Top & Bottom Rough trim station with superimposed motors (1.0 HP - 12,000 RPM); quick change motors Top & bottom Fine trim station with "Quick Change" motors (1.0 HP - 12,000 RPM motors), digital readouts for easy setup, Motors tilt 0-30° (4) Motor (0.47 HP - 12,000 RPM motors) station for corner rounding unit for trimming leading & trailing upper & lower edge/corners Top & bottom scrapers for 3 mm thick PVC banding. Top & bottom Post heat; hot air blowers with temperature adjustment. Feed track with "anti-slip" "Quick Change" snap on 80 mm wide X 60 mm long rubber pads, low friction nylon-graphite self-lubrication chain pads; 3 HP feeddrive. PLC microprocessor control for workstations w/keypad and LCD readout, insulated sound enclosure over all trim stations, industrial lights and viewing windows, extendible side panel support rail.
|
0.4 - 15mm capacity with 10 & 20 m/min feed speed; Min. panel width 85 mm & Min. length 160 mm, max. panel thickness 45 mm; automatic strip & coil feed magazine with robust shear type 3 mm PVC guillotine.Teflon coated Hot Melt glue pot, digital thermostats with automatic kick down when machine is in idle mode; dual temperature control Pressure section with (1) large dia. "non-stick" coated drive roller & (3) chrome plated pneumatic inclined pressure controlled idle rollers; horiz. adj. w/digital indicator. Workstations: Front & rear end trims (0.5 HP - 12,000 RPM motors), motors travel on 45° slides and pneumatic tilt 0° - 15° on horz. plane. Top & Bottom Rough trim station with superimposed motors (1.0 HP - 12,000 RPM); quick change motors Top & bottom Fine trim station with "Quick Change" motors (1.0 HP - 12,000 RPM motors), digital readouts for easy setup, Motors tilt 0-30° (4) Motor (0.47 HP - 12,000 RPM motors) station for corner rounding unit for trimming leading & trailing upper & lower edge/corners Top & bottom scrapers for 3 mm thick PVC banding. Top & bottom Post heat; hot air blowers with temperature adjustment. Feed track with "anti-slip" "Quick Change" snap on 80 mm wide X 60 mm long rubber pads, low friction nylon-graphite self-lubrication chain pads; 3 HP feeddrive. PLC microprocessor control for workstations w/keypad and LCD readout, insulated sound enclosure over all trim stations, industrial lights and viewing windows, extendible side panel support rail.
